{
 "title": "Nearest ASTM and SAE specifications",
 "checked": "2026-11-20",
 "rows": [
  {
   "EN 10305 part": "Part 1: seamless, cold drawn",
   "Nearest specification": "ASTM A519/A519M",
   "What that specification covers": "Seamless carbon and alloy steel mechanical tubing, hot-finished or cold-finished. Round tubes up to 12 3/4 in (325 mm) outside diameter; also square, rectangular and special shapes.",
   "Why it is not an equivalent (our reading)": "Broader than Part 1: it also covers hot-finished tubing, alloy steels and non-round shapes, and its range for round tubes ends at 325 mm where the scope of Part 1 ends at 380 mm.",
   "Sources": "https://store.astm.org/a0519_a0519m-24a.html"
  },
  {
   "EN 10305 part": "Part 2: welded, cold drawn",
   "Nearest specification": "ASTM A513/A513M, Type 5 (DOM)",
   "What that specification covers": "Electric-resistance-welded carbon and alloy steel mechanical tubing that is drawn over a mandrel.",
   "Why it is not an equivalent (our reading)": "A513 is a single specification for all electric-resistance-welded mechanical tubing. Drawn tube is one of several types in it, and grades, tolerances and conditions are defined on its own terms.",
   "Sources": "https://store.astm.org/a0513_a0513m-25.html"
  },
  {
   "EN 10305 part": "Part 3: welded, cold sized",
   "Nearest specification": "ASTM A513/A513M, Types 1a, 1b and 2",
   "What that specification covers": "Electric-resistance-welded mechanical tubing supplied as welded, made from hot-rolled or cold-rolled steel, in round, square, rectangular and special shapes.",
   "Why it is not an equivalent (our reading)": "A513 tells its as-welded types apart by the strip they are made from. Trade listings for Part 3 tell tubes apart by delivery condition (+CR1, +CR2, +N).",
   "Sources": "https://store.astm.org/a0513_a0513m-25.html"
  },
  {
   "EN 10305 part": "Part 4: seamless, hydraulic lines",
   "Nearest specification": "ASTM A822/A822M",
   "What that specification covers": "Seamless cold-drawn carbon steel tubing for hydraulic system service where forming needs tight-radius bending and flaring. Typical sizes 1/8 to 3 1/2 in (3.2 to 88.9 mm) outside diameter; heat treated after the final cold-working operation.",
   "Why it is not an equivalent (our reading)": "Written for hydraulic service like Part 4, but with its own sizes, heat treatment wording and tests. Its typical sizes end at 88.9 mm outside diameter.",
   "Sources": "https://store.astm.org/a0822_a0822m-20.html"
  },
  {
   "EN 10305 part": "Part 4: seamless, hydraulic lines",
   "Nearest specification": "SAE J524",
   "What that specification covers": "Cold drawn and annealed seamless low-carbon steel pressure tubing for hydraulic lines and other uses that need flaring and bending.",
   "Why it is not an equivalent (our reading)": "An SAE standard, not ASTM, for annealed hydraulic line tubing. A separate specification with its own requirements.",
   "Sources": "https://saemobilus.sae.org/standards/j524_202512-seamless-low-carbon-steel-tubing-annealed-bending-flaring"
  },
  {
   "EN 10305 part": "Part 5: square, rectangular",
   "Nearest specification": "ASTM A513/A513M, square and rectangular shapes",
   "What that specification covers": "The same specification covers square and rectangular electric-resistance-welded mechanical tubing.",
   "Why it is not an equivalent (our reading)": "Square and rectangular tubing is a shape inside A513, never a separate document as it was in EN 10305 until 2023.",
   "Sources": "https://store.astm.org/a0513_a0513m-25.html"
  },
  {
   "EN 10305 part": "Part 6: welded, hydraulic lines",
   "Nearest specification": "SAE J525",
   "What that specification covers": "Normalized, electric-resistance-welded, cold-drawn, single-wall low-carbon steel pressure tubing for pressure lines and other uses that need bending, flaring, forming and brazing.",
   "Why it is not an equivalent (our reading)": "An SAE standard, not ASTM. We found no ASTM specification written specifically for welded cold drawn hydraulic line tubing; A513 Type 5 covers the product form as mechanical tubing.",
   "Sources": "https://saemobilus.sae.org/standards/j525_202511-welded-cold-drawn-low-carbon-steel-tubing-annealed-bending-flaring"
  }
 ]
}